Configuration on Digi Hunch

Key mapping for external PC keyboard on Mac

Wed, 23 Nov 2022 10:38:00 -0400

This post is to document my steps to use external Windows keyboard on Mac with custom key mapping.

Background

Apple’s magic keyboard does not support multi-device so I have to repurpose my Logitech K810 keyboard with MacBook. Logitech K810 is and old model with Windows key layout even though it also supports MacOS.

The bottom row has the same number of keys as magic keyboard but with different keys. For example, magic keyboard has cmd key (aka GUI keys) besides space bar but K810 has Alt. Magic keyboard has Option key next to cmd key and K810 has Windows key on the left and Ctrl key on the right. The position of left Ctrl and FN is different on magic keyboard too. Since I rely on shortcuts on Magic keyboard, I therefore decide configure key mapping on the Windows key, Alt keys and right ctrl key to match magic keyboard.

K810 Layout

In a nutshell, I need to remap some keys on an external Windows keyboard connected to MacOS (Monterey).

What is not working

In MacOS, you could modify keys from keyboard preference as below. However, in my case I need to keep left ctrl key and overwrite the right ctrl key. MacOS does not distinguish them unfortunately. The native method is not flexible so I did not bother.

Use MacOS keyboard preference to modify keys

In the mean time, I hate to install a third-party application (such as Karabiner-Elements) just for the purpose of key mapping. Even though I appreciate the efforts by the community, I just don’t find it a neat solution for the additional dependency.

Challenges with key mapping

I then came across a developer’s post on using a utility called hidutil to map keys. This is promising after I tested using this command to swap key a/A and b/B.

hidutil property --set '{"UserKeyMapping":[{"HIDKeyboardModifierMappingSrc": 0x700000004,"HIDKeyboardModifierMappingDst": 0x700000005},{"HIDKeyboardModifierMappingSrc": 0x700000005,"HIDKeyboardModifierMappingDst": 0x700000004}]}'

The command above takes effect immediately, on all keyboards. In my case I only need mapping on an external keyboard, not the built-in keyboard. Luckily hidutil has –matching switch where I can specify ProductID and VendorID. I can find both of them from About This Mac -> System Report -> Hardware -> Bluetooth:

Vendor ID and Product ID

From this technical note, we can find out the usage IDs of the keys in the table at the bottom of the page. Then use the Usage ID as the last two bytes of the source and destination values of the mapping expression above. For example, 0x700000004 stands for key A/a, and 0x700000005 stands for key B/b. In my case, after going through this table, my key mapping is:

Source Key on K810	Source Code on K810	Destination Key	Destination Code
Left Alt	0x7000000E2	Left GUI (cmd)	0x7000000E3
Right Alt	0x7000000E6	Right GUI (cmd)	0x7000000E7
Left Win	0x7000000E3	Left Alt (option)	0x7000000E2
Right Ctrl	0x7000000E4	Right Alt (option)	0x7000000E6
Fn+F12	0x700000045	Globe	0xFF00000003

There is even a website that helps you generate the usage ID. I put together a command, which is working, on the external keyboard.

hidutil property --matching '{"ProductID":0xB319,"VendorID":0x046D}' --set '{"UserKeyMapping":[{"HIDKeyboardModifierMappingSrc":0x7000000E2,"HIDKeyboardModifierMappingDst":0x7000000E3},{"HIDKeyboardModifierMappingSrc":0x7000000E6,"HIDKeyboardModifierMappingDst":0x7000000E7},
{"HIDKeyboardModifierMappingSrc":0x7000000E3,"HIDKeyboardModifierMappingDst":0x7000000E2},
{"HIDKeyboardModifierMappingSrc":0x7000000E4,"HIDKeyboardModifierMappingDst":0x7000000E6},
{"HIDKeyboardModifierMappingSrc":0x700000045,"HIDKeyboardModifierMappingDst":0xFF00000003}
]}'

The other way to confirm that key mapping is working, is to look up key mapping with the following command:

hidutil property --matching '{"ProductID":0xB319,"VendorID":0x046D}' --get "UserKeyMapping"

To wipe out the mapping, we can use the following command:

hidutil property --matching '{"ProductID":0xB319,"VendorID":0x046D}' --set '{"UserKeyMapping":[]}'

Note that we have to use the same matching expression. However, I noticed that the command only works while the bluetooth keyboard is connected. When I reboot the MacBook the mapping goes away as well.

The solution to key mapping

Even though I could run this command after reboot using a plist file in ~/Library/LaunchAgents/, as the reference blog suggests, it will not work because I cannot guarantee the bluetooth keyboard is connected before MacOS executes it. Also, I might disconnect and re-connect the keyboard and I want to ensure that the system runs that command whenever the keyboard gets connected.

In the Karabiner Element community, some developers touched on this. Basically we can customize the plist file to tell MacOS when to fire the hidutil command, by using “LaunchEvents” key in the XML. There is an example for USB keyboard. For myself, I edit the plist file to be:

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
 <key>Label</key>
 <string>local.hidutilKeyMapping</string>
 <key>LaunchEvents</key>
 <dict>
 <key>com.apple.iokit.matching</key>
 <dict>
 <key>com.apple.bluetooth.hostController</key>
 <dict>
 <key>IOProviderClass</key>
 <string>IOBluetoothHCIController</string>
 <key>idProduct</key>
 <integer>B319</integer>
 <key>idVendor</key>
 <integer>046D</integer>
 <key>IOMatchLaunchStream</key>
 <true/>
 </dict>
 </dict>
 </dict> 
 <key>ProgramArguments</key>
 <array>
 <string>/usr/bin/hidutil</string>
 <string>property</string>
 <string>--matching</string>
 <string>{"ProductID":0xB319,"VendorID":0x046D}</string>
 <string>--set</string>
 <string>{
 "UserKeyMapping": [
 { 
 "HIDKeyboardModifierMappingSrc":0x7000000E2,
 "HIDKeyboardModifierMappingDst":0x7000000E3
 },
 { 
 "HIDKeyboardModifierMappingSrc":0x7000000E6,
 "HIDKeyboardModifierMappingDst":0x7000000E7
 },
 { 
 "HIDKeyboardModifierMappingSrc":0x7000000E3,
 "HIDKeyboardModifierMappingDst":0x7000000E2
 },
 { 
 "HIDKeyboardModifierMappingSrc":0x7000000E4,
 "HIDKeyboardModifierMappingDst":0x7000000E6
 },
 {
 "HIDKeyboardModifierMappingSrc":0x700000045,
 "HIDKeyboardModifierMappingDst":0xFF00000003
 }
 ]
 }</string>
 </array>

 <key>RunAtLoad</key>
 <true/>
</dict>
</plist>

Store the file above as ~/Library/LaunchAgents/com.local.hidutilKeyMapping.plist (create LaunchAgents directory if it doesn’t exist) and then run the following to load it:

launchctl load ~/Library/LaunchAgents/com.local.hidutilKeyMapping.plist

This works perfectly. The dict section (line 7 to line 23) of the file is based on this document as the GitHub comment suggests. The LaunchEvents section narrows down the type of events that will trigger the program with arguments. It triggers whenever a bluetooth device with specific ProductID and VendorID connects to Mac.

We can still use hidutil command from the previous section to ensure that the custom key mapping remain in effect:

Note that the output above has usage values converted to decimal from hexadecimal, with destination on top and source at the bottom.

I like this solution as it is light-weight, targeting a specific event, highly customizable and resolves an issue in a very specific circumstance.

Final words

K380 layout

After all this customization effort, I came across the Logitech K380 model (current alternative to K810), whose layout is exactly the way I customized K810 to be. So I ordered the new K380 model for just $29.99 during the week of black Friday. Remembering that I had my K810 for $94.98 back in 2015, what’s the point of all this….

Knative Eventing Introduction

Fri, 29 Apr 2022 10:16:00 -0400

In the previous post, I mentioned that Knative Serving and Knative Eventing should be seen as two different projects. The former is supposed to be widely used as a serving layer for microservices, whereas the latter has a narrower customer base. There are a dozen companies who need to build Platform as a Service, and will benefit from event-driven architecture. They are the niche customer for Knative Eventing. In this post, we go through two demos for Eventing.

Event Driven Architecture

Before jumping into Knative eventing, let’s first understand the value of event-driven architecture. As covered in Knative presentation in 2020, a growing micro-service architecture involves lots of service-to-service communications that looks like a spider web in a diagram. Two services communicating with each other are tightly coupled: changing one requires a change of the other. Event-driven architecture evolves to decouple those interdependent services. Knative eventing tries to standardize the event data with Cloud Event and also proposes a framework to drive this architecture.

The documentation uses different words to express the same concepts. So let’s take a note first: source = producer which emits events, and sink = subscriber = consumer which is the destination of events. Knative Eventing supports two models of in even-driven architecture.

Brokers and Triggers provides an “event mesh”. Event producers delivers events to a Broker. Triggers then distribute them uniformly by consumers.

Broker is a “hub” for events. It is a central location to receive and send events for delivery. We can choose from the following broker types:

MT (multi-tenant) channel-based broker (which a channel implementation, such as Kaka channel or an in-memory channel)
GCP broker
Apache Kafka broker
RabbitMQ broker

Triggers represents a desire to subscribe to events from a specific broker. It can act as a filter

channel-subscriber model

Channels and Subscriptions provide a “event pipe” model which transforms and routes events between Channels using Subscriptions. This model makes more sense when events out of one system needs to be transformed and then routed to another process.

A channel can be either a generic channel object, or a custom channel implementation (such as Kafka channel or in-memory channel)

The subscription consists of a Subscription object, which specifies the Channel and the Sink (aka the Subscriber) to deliver events to. You can also specify some Sink-specific options, such as how to handle failures.

The key difference is Broker-Trigger model allows you to filter events, where as Channel-Subscription model allows you to transform events.

Note that a Knative Service can act as both a Source and a Sink for events, and for good reason. You may want to consume events from the Broker and send modified events back to the Broker, as you would in any pipeline use-case. Between these components, Knative Eventing uses CloudEvents to send information back and forth.

Knative Eventing Lab

We can create a lab cluster using Kind as per the instruction in real-quicK-cluster. In docker-desktop settings, I configured 6 CPU and 8GB memory as the lab involves a number of nodes. The creation takes a couple minutes. This Knative eventing lab has four paths one can take, based on different model and different implementations:

Lab A demonstrates the configuration of broker-trigger model using Kafka based broker.
Lab B demonstrates the configuration of channel-subscription model, using in-memory channel.

The two labs share some common steps. We first install Knative Eventing using the provided manifests:

$ kubectl apply -f https://github.com/knative/eventing/releases/download/knative-v1.3.0/eventing-crds.yaml
$ kubectl apply -f https://github.com/knative/eventing/releases/download/knative-v1.3.0/eventing-core.yaml
$ kubectl get pods -n knative-eventing

The Pods should come to READY fairly quickly. In the mean time, we can configure the consumer as well using the manifests below:

apiVersion: v1
kind: Namespace
metadata:
 name: event-example
---
apiVersion: apps/v1
kind: Deployment
metadata:
 name: hello-display
 namespace: event-example
spec:
 replicas: 1
 selector:
 matchLabels: &labels
 app: hello-display
 template:
 metadata:
 labels: *labels
 spec:
 containers:
 - name: event-display
 image: gcr.io/knative-releases/knative.dev/eventing/cmd/event_display
---
kind: Service
apiVersion: v1
metadata:
 name: hello-display
 namespace: event-example
spec:
 selector:
 app: hello-display
 ports:
 - protocol: TCP
 port: 80
 targetPort: 8080
---
apiVersion: apps/v1
kind: Deployment
metadata:
 name: goodbye-display
 namespace: event-example
spec:
 replicas: 1
 selector:
 matchLabels: &labels
 app: goodbye-display
 template:
 metadata:
 labels: *labels
 spec:
 containers:
 - name: event-display
 image: gcr.io/knative-releases/knative.dev/eventing/cmd/event_display
---
kind: Service
apiVersion: v1
metadata:
 name: goodbye-display
 namespace: event-example
spec:
 selector:
 app: goodbye-display
 ports:
 - protocol: TCP
 port: 80
 targetPort: 8080

The consumers (aka sinks) will be able to process events at the validation step at the end.

Lab A – Install Kafka and configure Kafka-based Broker

This lab is for broker-trigger model. We first configure a Kafka Broker, which requires a Kafka cluster. The document uses Strimzi operator to quickly install Kafka cluster. Instead, here we use Helm to install the Kafka cluster:

helm install my-cluster-kafka bitnami/kafka -n kafka --create-namespace --set volumePermissions.enabled=true --set replicaCount=3

At the end of installation, the Helm notes indicate that the bootstrap server is my-cluster-kafka.kafka.svc.cluster.local:9092. All Kafka pods should come ready in about 5 minutes. After cluster install, we need to install Kafka controller and the Broker-layer data plane which allow you to map a Kafka instance to Broker CRD later:

kubectl apply -f https://github.com/knative-sandbox/eventing-kafka-broker/releases/download/knative-v1.3.0/eventing-kafka-controller.yaml
kubectl apply -f https://github.com/knative-sandbox/eventing-kafka-broker/releases/download/knative-v1.3.0/eventing-kafka-broker.yaml
kubectl get pods -n knative-eventing
kubectl -n knative-eventing edit cm kafka-broker-config

As the command above suggests, once data plane is installed, we edit the default broker config by updating the bootstrap.servers with the bootstrap server address noted above. We also need to make sure the replication factor is no greater than number of partitions, which should not be a problem in our lab as the replica count was set to 3.

Now we can create a Broker in the same namespace with consumer:

apiVersion: eventing.knative.dev/v1
kind: Broker
metadata:
 name: default
 namespace: event-example
 annotations:
 eventing.knative.dev/broker.class: Kafka
spec:
 config:
 apiVersion: v1
 kind: ConfigMap
 name: kafka-broker-config
 namespace: knative-eventing

Once the manifest above is applied, we should see the status of broker (named default) to be READY. We can also validate broker creation with kn CLI command:

 $ kubectl -n event-example get broker default
NAME URL AGE READY REASON
default http://kafka-broker-ingress.knative-eventing.svc.cluster.local/event-example/default 19m True
$ kn broker list -n event-example
NAME URL AGE CONDITIONS READY REASON
default http://kafka-broker-ingress.knative-eventing.svc.cluster.local/event-example/default 19m 7 OK / 7 True

Then we create Triggers that connects both to the broker with filters, and to the consumers by referencing service name. The manifest to create triggers is provided below:

apiVersion: eventing.knative.dev/v1
kind: Trigger
metadata:
 name: hello-display
 namespace: event-example
spec:
 broker: default
 filter:
 attributes:
 type: greeting
 subscriber:
 ref:
 apiVersion: v1
 kind: Service
 name: hello-display
---
apiVersion: eventing.knative.dev/v1
kind: Trigger
metadata:
 name: goodbye-display
 namespace: event-example
spec:
 broker: default
 filter:
 attributes:
 source: sendoff
 subscriber:
 ref:
 apiVersion: v1
 kind: Service
 name: goodbye-display

We can confirm the setups above by monitoring the resources (like we did for broker), or use knative CLI:

$ kn trigger list -n event-example
NAME BROKER SINK AGE CONDITIONS READY REASON
goodbye-display default service:goodbye-display 3m24s 6 OK / 6 True
hello-display default service:hello-display 3m24s 6 OK / 6 True

Now we can go to the validation step to send event and validate result.

Lab B – Install in-memory channel and configure Channel

This lab is for channel-subscription model. we first install an in-memory channel:

kubectl apply -f https://github.com/knative/eventing/releases/download/knative-v1.3.0/in-memory-channel.yaml

Then we can map this channel to a Channel resource in Eventing. We can do so by applying the manifest below:

apiVersion: messaging.knative.dev/v1
kind: Channel
metadata:
 name: demo-channel-1
 namespace: event-example
---
apiVersion: messaging.knative.dev/v1
kind: Channel
metadata:
 name: demo-channel-2
 namespace: event-example

The creation of Channel resources can be verified as below

$ kn -n event-example channel list
NAME TYPE URL AGE READY REASON
demo-channel-1 InMemoryChannel http://demo-channel-1-kn-channel.event-example.svc.cluster.local 6m34s True
demo-channel-2 InMemoryChannel http://demo-channel-2-kn-channel.event-example.svc.cluster.local 6m34s True

Now we need to create Subscription which connects Channels to Consumers. Subscriptions can be created with the manifest below:

apiVersion: messaging.knative.dev/v1
kind: Subscription
metadata:
 name: demo-subscription-1
 namespace: event-example
spec:
 channel:
 apiVersion: messaging.knative.dev/v1
 kind: Channel
 name: demo-channel-1
 subscriber:
 ref:
 apiVersion: v1
 kind: Service
 name: hello-display
---
apiVersion: messaging.knative.dev/v1
kind: Subscription
metadata:
 name: demo-subscription-2
 namespace: event-example
spec:
 channel:
 apiVersion: messaging.knative.dev/v1
 kind: Channel
 name: demo-channel-2
 subscriber:
 ref:
 apiVersion: v1
 kind: Service
 name: goodbye-display

We can confirm subscription:

$ kn -n event-example subscription list
NAME CHANNEL SUBSCRIBER REPLY DEAD LETTER SINK READY REASON
demo-subscription-1 Channel:demo-channel-1 service:hello-display True
demo-subscription-2 Channel:demo-channel-2 service:goodbye-display True

Now we can go to validation step.

Validation

For validation, we need to first configure an event source. The source in our lab is a throw-away Pod with curl utility. I use my favourite nicolaka netshoot to fire off the events using. To launch the Pod and get to command shell:

$ kubectl run tmp-shell -n event-example --rm -i --tty --image nicolaka/netshoot -- /bin/bash
If you don't see a command prompt, try pressing enter.
bash-5.1#

We can POST message to the corresponding endpoint URL to fire events. The endpoint is different for each lab:

Lab	URL
A (Kafka-based broker)	http://kafka-broker-ingress.knative-eventing.svc.cluster.local/event-example/default
B (channel)	http://demo-channel-1-kn-channel.event-example.svc.cluster.local http://demo-channel-2-kn-channel.event-example.svc.cluster.local

With the correct URL, we can build a payload for POST method. Below is three curl commands with different payload POST to the same endpoint (taking lab A as an example):

# curl -v "http://broker-ingress.knative-eventing.svc.cluster.local/event-example/default" \
-X POST \
-H "Ce-Id: say-hello" \
-H "Ce-Specversion: 1.0" \
-H "Ce-Type: greeting" \
-H "Ce-Source: not-sendoff" \
-H "Content-Type: application/json" \
-d '{"msg":"Hello Knative!"}'

# curl -v "http://broker-ingress.knative-eventing.svc.cluster.local/event-example/default" \
-X POST \
-H "Ce-Id: say-goodbye" \
-H "Ce-Specversion: 1.0" \
-H "Ce-Type: not-greeting" \
-H "Ce-Source: sendoff" \
-H "Content-Type: application/json" \
-d '{"msg":"Goodbye Knative!"}'

# curl -v "http://broker-ingress.knative-eventing.svc.cluster.local/event-example/default" \
-X POST \
-H "Ce-Id: say-hello-goodbye" \
-H "Ce-Specversion: 1.0" \
-H "Ce-Type: greeting" \
-H "Ce-Source: sendoff" \
-H "Content-Type: application/json" \
-d '{"msg":"Hello Knative! Goodbye Knative!"}'

All the requests should receive 202 return code. As highlighted above, we specified type and source for each event fired to the broker. On the consumer side, we can simply check the pod log to verify the events received. Below is an example of events received as a result of the events sent above (take broker-trigger model as example):

$ kubectl -n event-example logs -l app=hello-display --tail=100
2022/03/09 17:05:59 Failed to read tracing config, using the no-op default: empty json tracing config
☁️ cloudevents.Event
Context Attributes,
 specversion: 1.0
 type: greeting
 source: not-sendoff
 id: say-hello
 datacontenttype: application/json
Extensions,
 knativearrivaltime: 2022-03-09T17:14:19.196589801Z
Data,
 {
 "msg": "Hello Knative!"
 }
☁️ cloudevents.Event
Context Attributes,
 specversion: 1.0
 type: greeting
 source: sendoff
 id: say-hello-goodbye
 datacontenttype: application/json
Extensions,
 knativearrivaltime: 2022-03-09T17:14:42.977803608Z
Data,
 {
 "msg": "Hello Knative! Goodbye Knative!"
 }
$ kubectl -n event-example logs -l app=goodbye-display --tail=100
2022/03/09 17:05:58 Failed to read tracing config, using the no-op default: empty json tracing config
☁️ cloudevents.Event
Context Attributes,
 specversion: 1.0
 type: not-greeting
 source: sendoff
 id: say-goodbye
 datacontenttype: application/json
Extensions,
 knativearrivaltime: 2022-03-09T17:14:27.430702588Z
Data,
 {
 "msg": "Goodbye Knative!"
 }
☁️ cloudevents.Event
Context Attributes,
 specversion: 1.0
 type: greeting
 source: sendoff
 id: say-hello-goodbye
 datacontenttype: application/json
Extensions,
 knativearrivaltime: 2022-03-09T17:14:42.977803608Z
Data,
 {
 "msg": "Hello Knative! Goodbye Knative!"
 }

This is the gist of Knative evening. Note that the format of HTTP payload when we fire off events needs to conform to CloudEvents format. The container image (event_display) used in the container is also created for the purpose of processing events received and display them in stdout.

Conclusion

Persistent storage allows for stateful applications on Kubernetes. It also enables architectural patterns that requires persistent storage. Knative eventing is a framework that enables event driven architecture. It supports many messaging channels (including NATs, a cloud-native messaging system) and broker types (MT channel based, GCP, RabbitMQ).

Knative Serving Introduction

Sun, 17 Apr 2022 11:33:00 -0400

Background

As per IBM‘s definition, Knative enables serverless workloads to run on Kubernetes clusters, and makes building and orchestrating containers with Kubernetes faster and easier. It has drawn a lot of attention recently. It released version 1.0 in November 2021, and was accepted as a CNCF incubating project in March 2022.

Glories aside, the value it delivers is the ability to go serverless on a Kubernetes platform. Originally, Knative was built with three components: build, serving and eventing. The build component was deprecated in favour of the Tekton project. Tekton is cloud native CI/CD pipeline. It connects to source code repo and build artifacts. It can also deploy applications with pipeline as code. Tekton’s documentation includes a quality tutorial here linked to interactive terminal. On the other hand, we’ll focus on Knative Serving in this post, and Knative Eventing in the next.

Knative can be seen as a serverless framework with a number of open-source technologies as building blocks, such as Istio for ingress gateway, Kafka or Google Pub/Sub as event-streaming engine, and Prometheus for observability to name a few. Despite of using the same CLI tool (named kn), Knative Serving and Eventing are considered separate capabilities using different groups of CRDs. They are installed separately, using their respective YAML files, or operator.

Serving vs Eventing ?

After reading the article “Did we market Knative wrong” from Ahmet Balkan, my impression is the two are not related. They could have been two separate projects without sharing a common name. As the author puts, these two shared some core logics. But beyond that, they don’t have anything in common.

Serving is lightweight and requires Istio. It provides the capability to scale from N to 0 when the system is idle, and from 0 to N when requests come in. It is the missing serving layer for running microservices on Kubernetes and Ahmet position it as the first thing that people installed after creating a cluster.

The target user of Eventing is much smaller. Eventing is for event-driven architecture and is more complex than Serving. Ahmet admits that they over-estimated how many people on the planet want to build a Heroku-like PaaS layer on top of Knative. There are a couple of dozen companies who would work through the complexity and build their own Kubernetes-based internal PaaS or even public-facing FaaS using Knative. They are the niche audience of Knative Eventing.

For most platform builders who just need to run micro-service, Knative Serving is all they need.

A Demo on Serving

The definition of term “serverless” is very loose. Instead, Knative documentation promotes the ability to scale to zero and refer to it as “some people call this Serverless”. This suggests that “the ability to scale to zero” should be the better term to describe this capability. To deploy it, we need the Service object with apiVersion serving.knative.dev/v1. Below is a guide for a quick hands-on, with some steps modified from the Knative Serving tutorial and installation guide, with optional steps (extensions, DNS) skipped.

Follow the first part of this post or this guide in real-quicK-cluster project, to install minikube with metal LB and configure istio (using istioctl as per instruction). Then Knative serving can be installed with two YAML manifests:

$ kubectl apply -f https://github.com/knative/serving/releases/download/knative-v1.2.0/serving-crds.yaml
$ kubectl apply -f https://github.com/knative/serving/releases/download/knative-v1.2.0/serving-core.yaml

Then we can install Knative istio controller to integrate them so we can see the knative gateways:

$ kubectl apply -f https://github.com/knative/net-istio/releases/download/knative-v1.2.0/net-istio.yaml
$ kubectl -n knative-serving get gateway

Now we can install the dummy service, either using kn CLI tool or using YAML manifest. The manifest is given below:

apiVersion: serving.knative.dev/v1
kind: Service
metadata:
 name: hello
 namespace: default
spec:
 template:
 metadata:
 name: hello-world
 annotations:
 autoscaling.knative.dev/class: "kpa.autoscaling.knative.dev"
 autoscaling.knative.dev/metric: "rps"
 autoscaling.knative.dev/target: "50"
 autoscaling.knative.dev/min-scale: "0"
 autoscaling.knative.dev/max-scale: "10"
 spec:
 containerConcurrency: 0
 containers:
 - env:
 - name: TARGET
 value: World
 image: gcr.io/knative-samples/helloworld-go
 name: user-container
 ports:
 - containerPort: 8080
 protocol: TCP

We can notice that in the annotations there are some settings to overwrite the default configuration. They are explained in the autoscaling section of the Knative serving documentation. Here we use request per second (rps) as metric, and have 50 as target. The scale range is between 3 and 10 replicas. Once the resource is created, we can validate it with one of the two commands:

$ kubectl get services.serving.knative.dev
$ kn service describe hello

The creation of knative service also created a number of Kubernetes resources, such as deployment and services:

$ kubectl get svc
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
hello ExternalName <none> knative-local-gateway.istio-system.svc.cluster.local 80/TCP 52s
hello-world ClusterIP 10.110.127.231 <none> 80/TCP 108s
hello-world-private ClusterIP 10.111.27.73 <none> 80/TCP,9090/TCP,9091/TCP,8022/TCP,8012/TCP 108s
kubernetes ClusterIP 10.96.0.1 <none>
$ kubectl get deploy
NAME READY UP-TO-DATE AVAILABLE AGE
hello-world-deployment 1/1 1 1 71s

Before testing, let’s mock the DNS entry to resolve to the Istio ingress service IP like below in /etc/hosts:

192.168.64.16 hello.default.example.com

Now we can confirm that the service returns the expected result (after a brief pause):

$ curl hello.default.example.com
Hello World!

Wait for a short period without curl or connection from browser, the service should scale down to zero:

$ kubectl get deploy -l serving.knative.dev/service=hello -w
NAME READY UP-TO-DATE AVAILABLE AGE
hello-world-deployment 0/0 0 0 78s

From a separate terminal, emulate HTTP request with hey command, so the service receives more than 50 rps per pod:

$ hey -n 200 -c 20 -z 20s -m GET http://hello.default.example.com

We can watch the deployment get scaled up to 10. Once the hey command completes its task, the deployment will scale back down:

$ kubectl get deploy -l serving.knative.dev/service=hello -w
NAME READY UP-TO-DATE AVAILABLE AGE
hello-world-deployment 0/0 0 0 78s
hello-world-deployment 0/1 0 0 3m54s
hello-world-deployment 0/1 0 0 3m54s
hello-world-deployment 0/1 0 0 3m54s
hello-world-deployment 0/1 1 0 3m54s
hello-world-deployment 1/1 1 1 4m2s
hello-world-deployment 1/10 1 1 4m4s
hello-world-deployment 1/10 1 1 4m4s
hello-world-deployment 1/10 1 1 4m4s
hello-world-deployment 1/10 10 1 4m5s
hello-world-deployment 2/10 10 2 4m9s
hello-world-deployment 3/10 10 3 4m10s
hello-world-deployment 4/10 10 4 4m10s
hello-world-deployment 7/10 10 7 4m10s
hello-world-deployment 9/10 10 9 4m10s
hello-world-deployment 10/10 10 10 4m11s
hello-world-deployment 10/5 10 10 5m18s
hello-world-deployment 10/5 10 10 5m18s
hello-world-deployment 5/5 5 5 5m18s
hello-world-deployment 5/2 5 5 5m20s
hello-world-deployment 5/2 5 5 5m20s
hello-world-deployment 2/2 2 2 5m20s
hello-world-deployment 2/1 2 2 5m22s
hello-world-deployment 2/1 2 2 5m22s
hello-world-deployment 1/1 1 1 5m22s
hello-world-deployment 1/0 1 1 5m52s
hello-world-deployment 1/0 1 1 5m52s
hello-world-deployment 0/0 0 0 5m52s

Autoscaling in Knative serving is backed by KPA (Knative Pod Autoscaler, used in the example above) or HPA. Also note that the trigger to scale up and down is client connection (RPS). This is different than KEDA. KEDA also supports the capability to scale to zero. However, with KEDA, it is an event that scales a deployment up from zero. In Knative serving, it is the connection to the Service itself that wakes up the service.

Cost of scale-to-zero

As discussed, both KEDA and Knative serving supports the ability to scale to zero and wake up from zero. The trigger to wake up from zero is different. With KEDA, workload wakes up by an event. With Knative Serving, workload has to wake up upon receiving a connection to the service. In the design to solve this problem, Knative has four sub-components :

Activator – When a service is scaled to zero, its request are routed to the activator which waits for a Pod to become ready (wake up) and proxies the traffic while editing the underlying Endpoints to route the traffic directly to the Pod(s)
Autoscaler – KPA
Controller – The main component responsible for watching API objects for Knative CRDs (KService, Configuration, Route, Revision) and manage their lifecycle, create the underlying Kubernetes resources and garbage-collect old objects.
Webhook – a Kubernetes Admission Webhook acting both as validating admission controller and mutating admission controller.

The key player is activator, which receives requests when a service is scaled to zero. The wake-up process is summarized as follows:

After receiving request, activator will buffer (hold onto) the request
Then, it will look at request’s hostname to find which KService it is for.
Then, it will scale up the Kubernetes Deployment and wait for a Pod to become ready.
In the meanwhile, it updates Kubernetes Service to point to Pod IP addresses (so that activator gets out of the network path if the KService is awake).
Finally, activator proxies the request to the started pod

So the “plumbing” of the service connection managed by the Activator pod is the cost of scale to zero. This is also called Load Balancing, and the behaviour can be tweaked using two parameters: activator capacity and target burst capacity:

Target burst capacity: once the target deploy has one more more Pod, service requests may still route via activator or bypassing the activator. Target burst capacity determines at what point service request should start to bypass activator.
Activator capacity: determines how many requests can activator hold on to. Considering the service-to-service connection also routes via Service CRD, there can be a lot of connections via Activator so its capacity needs to be adjusted.

The additional overhead of managing and optimizing the “Load Balancer” is also part of operational cost for the ability to scale to zero.

In comparison, KEDA now has an HTTP add-on still at beta but allows connection-based wake-up. The design is a little different. As discussed in this previous post.

Conclusion

Knative consists of two disparate components: Serving and Eventing. Serving uses KPA to provide scaling based on service request, and the ability to scale to zero. It is often compared with KEDA, a single-purpose lightweight tool for autoscaling. Here is a blurb on their difference by KEDA. The takeaways is that KEDA is more focused on scalability, whereas Knative serving covers more aspects. For example, the Service object of Knative also supports Traffic Splitting. Knative serving can integrate with istio.

Service Proxy – from Nginx to Envoy

Wed, 09 Mar 2022 21:36:00 -0400

Update (Nov 20, 2022): 1. Envoy’s configuration schema can be hard to get used to. It is lacking examples because the documentation is mostly generated. Use its examples directory to find real-life configuration examples. 2. the Envoy implementation in the example project has been reverted in favour of Nginx.

Envoy proxy is the underlying technology for Istio, as well as a number of other service mesh products, such as AppMesh (AWS), Consul (Hashicorp) and OpenServiceMesh (Azure). Most of the capabilities of Isito is ultimately provided by Envoy proxy. Envoy has a page outlining its differences with similar technologies. I decided to take a look into Envoy by replacing Nginx with it.

Rate limiting and Circuit Breaker

In most SDLC, it is application developers that create backend APIs or server applications. Most developers specializes in application features, and cannot fathom all the nuances with the TCP/IP network stack. Nginx allows them to push network concerns (non-business features) to a dedicated proxy to handle the dynamics in network connection. Nginx can be configured as both a reverse proxy (handling incoming connection on behalf of the process) and a forward proxy (handling outgoing connection on behalf of the process). This is the prototype of sidecar pattern, an important idea behind service mesh. For example, when a sudden increase in connection to the server-side application, the server process could be either unresponsive (refer to “the queuing knee“, and Little’s Law), or OOM killed. When such interruptions are not automatically recovered, a downtime is caused. This traditionally requires some congestion control strategy for TCP/IP queue but two features provided by a network proxy can help circumvent this situation: rate limiting, and circuit breaking. Rate limiting keeps more requests above threshold from entering the queue. Circuit breaker releases downstream pressure by cutting out existing in-queue request. Nginx added both over the years but Circuit breaker still remains a premium feature exclusive to Nginx Plus. Envoy on the other hand has them free when it was launched.

Envoy also supports other advanced traffic management such as traffic shaping, and mirroring. It is on top of those features that Istio introduces its own abstraction such as virtual service, destination rules to its users. In that sense, we can think of Istio as a configurator (control plane) for Envoy proxy (data plane), similar to Ansible to Nginx proxy instances.

Dynamic Configuration via API

I used Nginx previously with traditional environment and loved its flexibility. As the system grows, I started to feel the pain of management overhead. With one of the production system, there were 25 + instances of Nginx each running on a VM and I managed configuration files with Ansible. Ansible pushes out configuration files and triggers a reload from each Nginx instance. In the cloud-native era where Pods are ephemeral, this kind of overhead would snowball to an unmanageable level. Envoy was designed for cloud-native applications, with all these kinds of problems in mind. Envoy has dynamic configuration. The majority of the configurations can be pulled from xDS API, or file system. Updating configuration drains connections gracefully without runtime having to reload the file. The idea of centrally managing Nginx instances with Ansible, also evolved into the concept of control plane.

TLS origination

In the Orthweb project, I used Nginx to proxy TLS and HTTP traffic, and performed TLS termination on both ports. This is know as TLS offloading. The traffic between the proxy and the upstream service takes place in the clear, even though they do not travel across different network interfaces in most cases. For a true end-to-end encryption, it is helpful to also encrypt the traffic between proxy and upstream server. This requires the capability of securing TCP traffic to upstream server. With Nginx, the ability to secure HTTP traffic to upstream server is offered in open-source. The ability to secure TCP traffic is available in Nginx Plus, or with self-compiled binary. In Envoy, both are available using the UpstreamTlsContext configuration.

More pros

In another post, I also discussed Nginx as a LDAP proxy to front services such as Kibana and Nifi. It requires a proxy service (ldap-auth in this case), to defer auth to third party. Envoy has this capability using a filter with extension for external authorization. Istio also exposes this capability, an enabler for the configuration proposed in my previous post. Envoy also uses WebAssembly for its extensibility.

Another useful feature is protocol detection. It can use filters to detect protocol (TLS or regular TCP) and route traffic to predefined destination.

Performance wise, this benchmark from 2018 ran a comparison among the popular options where Envoy leads by a margin.

Observability (logging, metrics and tracing) are well supported in Envoy. User can configure format of logs that takes effect immediately. There are many metrics that works with Prometheus and they are expandable using filters. On the tracing side, Envoy supports integration with jaeger, zipkin and datadog.

Basics of Envoy

The configuration of Envoy is more involving. There is an Envoy course by Tetrate, as well as two blog entries for envoy 101: Envoy as gateway proxy and File-based dynamic configuration. Another good way to get started is the Sandboxes projects, which covers a number of different areas of configuration. The admin port (by default at port 9901. Istio’s default is 15000) provides helpful information. If we need to turn on debug on some features, we can do so with curl:

curl -X POST http://localhost:9901/logging?client=debug

Stats are exposed at the same port:

curl -X GET http://localhost:9901/stats

When packets are received at a listener, the is first processed by listener filters. Then, depending on filter match, one or more network filter chains will further process the packet, including further actions, as illustrated below:

Envoy supports dynamic configuration, which uses a set of discovery services (xDS) APIs. Some of the important xDS APIs include:

LDS (Listener Discovery Service) – allows you to add listeners dynamically while Envoy is running
RDS (Route Discovery Service) – allows you to dynamically update routes for HTTP connection managers
CDS (Cluster Discovery Service) – allows you to update cluster definitions dynamically
EDS (Endpoint Discovery Service) – allows you to add or remove endpoints dynamically
Secret DS

The relation can be illustrated in this diagram below:

This post from Tetrate has more examples.

Nginx to Envoy

For the advantages of Envoy, I decided to migrate from Nginx to Envoy on my Orthweb project. Using Envoy as service proxy is not where Envoy is mostly used (as sidecar), but it is how Envoy was originally used at Lyft to replace ELB in 2015.

The original Nginx configuration was referenced in this old blog post. The Envoy setup also covers both TCP (DICOM) and HTTP (HTTPS) traffic. For HTTP traffic, it also encrypts the traffic to upstream. Below is what it looks like:

admin:
 address:
 socket_address: { address: 0.0.0.0, port_value: 9901 }
static_resources:
 listeners:
 - name: https_listener
 address:
 socket_address:
 address: 0.0.0.0
 port_value: 443
 filter_chains:
 - filters:
 - name: envoy.filters.network.http_connection_manager
 typed_config:
 "@type": type.googleapis.com/envoy.extensions.filters.network.http_connection_manager.v3.HttpConnectionManager
 codec_type: AUTO
 stat_prefix: ingress_http
 route_config:
 name: local_route
 virtual_hosts:
 - name: app
 domains:
 - "*"
 routes:
 - match:
 prefix: "/"
 route:
 cluster: service-https
 http_filters:
 - name: envoy.filters.http.router
 transport_socket:
 name: envoy.transport_sockets.tls
 typed_config:
 "@type": type.googleapis.com/envoy.extensions.transport_sockets.tls.v3.DownstreamTlsContext
 common_tls_context:
 tls_certificates:
 - certificate_chain: {"filename": "/etc/ssl/certs/site.pem"}
 private_key: {"filename": "/etc/ssl/certs/site.pem"}
 - name: dicomtls_listener
 address:
 socket_address:
 address: 0.0.0.0
 port_value: 11112
 filter_chains:
 - filters:
 - name: envoy.filters.network.tcp_proxy
 typed_config:
 "@type": type.googleapis.com/envoy.extensions.filters.network.tcp_proxy.v3.TcpProxy
 stat_prefix: downstream_cx_total
 cluster: service-dicomtls
 transport_socket:
 name: envoy.transport_sockets.tls
 typed_config:
 "@type": type.googleapis.com/envoy.extensions.transport_sockets.tls.v3.DownstreamTlsContext
 common_tls_context:
 tls_certificates:
 - certificate_chain: {"filename": "/etc/ssl/certs/site.pem"}
 private_key: {"filename": "/etc/ssl/certs/site.pem"}
 validation_context:
 allow_expired_certificate: true
 trusted_ca: {"filename": "/etc/ssl/certs/site.pem"}
 require_client_certificate: false
 clusters:
 - name: service-https
 type: STRICT_DNS
 lb_policy: ROUND_ROBIN
 load_assignment:
 cluster_name: service-https
 endpoints:
 - lb_endpoints:
 - endpoint:
 address:
 socket_address:
 address: orthanc-backend
 port_value: 8042
 transport_socket:
 name: envoy.transport_sockets.tls
 typed_config:
 "@type": type.googleapis.com/envoy.extensions.transport_sockets.tls.v3.UpstreamTlsContext
 - name: service-dicomtls
 type: STRICT_DNS
 lb_policy: ROUND_ROBIN
 load_assignment:
 cluster_name: service-dicomtls
 endpoints:
 - lb_endpoints:
 - endpoint:
 address:
 socket_address:
 address: orthanc-backend
 port_value: 4242
layered_runtime:
 layers:
 - name: static_layer_0
 static_layer:
 envoy:
 resource_limits:
 listener:
 https_listener:
 connection_limit: 1000
 overload:
 global_downstream_max_connections: 5000

From Nginx to Envoy, to achieve nearly the same functionalities, it takes 100 lines of configuration instead of less than 30. The configuration also appears more abstract, which is one of the cons of Envoy to consider before the migration.

Update from Jan 2025 – To align with what most uses in Orthanc community, the project switched back to using Nginx. The envoy configuration is kept here.

Istio Lab – Ingress and Egress

Tue, 16 Nov 2021 21:28:00 -0400

Istio is a popular open-source service mesh implementation using Envoy proxy. One of the benefit of using Istio is the ingress and egress it brings to native Kubernetes platform. This article is a hands-on guide to test Istio ingress and egress gateways on Minikube. It was tested on my MacBook. All the information in this post can be found in several different pages from Istio and Minikube documentation. The purpose of this article is a single cheat sheet for myself to quickly set up Istio ingress and egress testing.

Install Istio on Minikube

We start with configuring Minikube on MacBook (or change the command accordingly on other platform), and install metal LB load balancer. The steps with Istio also works with a regular Kubernetes platform.

minikube start --memory=12288 --cpus=6 --kubernetes-version=v1.20.2 --nodes 3 --container-runtime=containerd --driver=hyperkit
minikube addons enable metallb

Then we need to give load balancer an IP address range before setting up the load balancer. Minikube adds an interface named bridge100 to MacOS host environment. The IP address of the host can be found via the following command:

minikube ssh "ping host.minikube.internal -c 1"

For example, my host IP address is 192.168.64.1, so I dedicate the IP range 192.168.64.64 to 192.168.64.80 to the MetalLB load balancer. Then I need to provide this range when configuring the load balancer:

minikube addons configure metallb
kubectl -n metallb-system get po

After the configuration, make sure the MetalLB pod is up. Then we can install istio to the Kubernetes cluster. The steps are completed using istioctl following the instruction, I created a quick and dirty script to put the steps together:

#! /bin/bash
curl -L https://istio.io/downloadIstio | sh -
export PATH=$(realpath istio*/bin):$PATH
ln -sfn $(ls -d -- istio-*) istio
if istioctl x precheck; then
 echo ready to install istio and lable namespace for istio-injection
 istioctl install --set profile=demo -y --verify --set meshConfig.outboundTrafficPolicy.mode=REGISTRY_ONLY
 kubectl label namespace default istio-injection=enabled
else
 echo failed precheck
 exit 1
fi

The script above download the istio zip file, unzips it, installs Istio (in demo mode and set outboundTrafficPolicy to REGISTRY_ONLY), labels default namespace for proxy injection. To use istioctl without spelling out full path, we can run the following command again separately outside of script:

export PATH=$(realpath istio/bin):$PATH

To validate, check istioctl version command.

Install Sample application

For simplicity, the rest of this article uses httpbin to test Istio’s ingress and egress. For completeness, this section gives the steps to install bookinfo application as it is used in other Istio testing as well. It also help understand how to ingress to an application with Istio using an IP provided by the load balancer. Skip this section if just need to test with the simple httpbin application. The Bookinfo application comes within the istio 1.12 directory. In the following steps from the istio directory, we install some observability add-ons as well as the bookinfo application. Then we test access to the website.

kubectl apply -f samples/addons/prometheus.yaml
kubectl apply -f samples/addons/kiali.yaml
kubectl apply -f samples/addons/jaeger.yaml
kubectl apply -f samples/addons/grafana.yaml

kubectl apply -f samples/bookinfo/platform/kube/bookinfo.yaml
kubectl apply -f samples/bookinfo/networking/bookinfo-gateway.yaml

kubectl exec "$(kubectl get pod -l app=ratings -o jsonpath='{.items[0].metadata.name}')" -c ratings -- curl -sS productpage:9080/productpage | grep -o "<title>.*</title>"

export INGRESS_HOST=$(kubectl -n istio-system get service istio-ingressgateway -o jsonpath='{.status.loadBalancer.ingress[0].ip}')
export INGRESS_PORT=$(kubectl -n istio-system get service istio-ingressgateway -o jsonpath='{.spec.ports[?(@.name=="http2")].port}')
export GATEWAY_URL=$INGRESS_HOST:$INGRESS_PORT
curl -s "http://${GATEWAY_URL}/productpage" | grep -o "<title>.*</title>"

On my laptop, the value of $GATEWAY_URL is 192.168.64.64:80. Therefore I can browse to site http://192.168.64.64:80/productpage with local browser. We can also check kiali dashboard:

istioctl dashboard kiali

Then we are good to examine ingress and egress.

Prep Work

The following custom resources are related to traffic management in istio:

Virtual Service (vs)
Destination Rule (dr)
Service Entry (se)
Gateway (gw, Istio’s ingress or egress)

We will expand on the role of each in a separate article. To execute command from within a Pod, we also use sleep application which is essentially a Pod with a sleeper thread for the purpose allowing user to run troubleshooting command. The sleep application is provided in istio directory:

kubectl apply -f samples/sleep/sleep.yaml
kubectl get po -l app=sleep

Find out the Pod name to execute command. Then we use httpbin website to emulate an external service, and use the sleep Pod (suppose the name is sleep-557747455f-q99cz) to access the service:

kubectl exec -it sleep-557747455f-q99cz -c sleep -- curl http://httpbin.org/headers

As we previously set outboundTrafficPolicy.mode=REGISTRY_ONLY, this step is expected to output nothing. If this is not the case, it means the cluster may have ALLOW_ALL as outbount traffic policy, and you will need to follow this guide to set it to REGISTRY_ONLY. With REGISTRY_ONLY, in order to allow access, we need to register a service entry, by applying the document below:

apiVersion: networking.istio.io/v1alpha3
kind: ServiceEntry
metadata:
 name: httpbin
spec:
 hosts:
 - httpbin.org
 ports:
 - number: 80
 name: http
 protocol: HTTP
 resolution: DNS

Now we should be able to access httpbin service as it is registered:

kubectl get se httpbin -o yaml

Using the exec command above again, we should see output from the curl command.

Ingress Testing

We deploy an httpbin service in order to test ingress. The YAML declaration is prepared by Istio installation package:

kubectl apply -f samples/httpbin/httpbin.yaml

Then we deploy the ingress:

apiVersion: networking.istio.io/v1alpha3
kind: Gateway
metadata:
 name: httpbin-gateway
spec:
 selector:
 istio: ingressgateway
 servers:
 - port:
 number: 80
 name: http
 protocol: HTTP
 hosts:
 - "httpbin.digihunch.com"

The selector above indicates that the gateway deployed to a Pod labeled with istio: ingressgateway. Then we create a corresponding virtual service for this gateway:

apiVersion: networking.istio.io/v1alpha3
kind: VirtualService
metadata:
 name: httpbin
spec:
 hosts:
 - "httpbin.digihunch.com"
 gateways:
 - httpbin-gateway
 http:
 - match:
 - uri:
 prefix: /status
 - uri:
 prefix: /delay
 route:
 - destination:
 port:
 number: 8000
 host: httpbin

Note that the hosts setup must match the configuration in gateway. The virtual service defines two services at URIs /status and /delay to expose, and we can confirm the creation of virtual service:

kubectl get vs httpbin -o yaml

We can then test with curl command from MacOS host to verify that the ingress is working. We need to use the IP address of the service (192.168.64.64 with port 80 as previously indicated):

curl -I -HHost:httpbin.digihunch.com http://192.168.64.64/status/200
curl -I -HHost:httpbin.digihunch.com http://192.168.64.64/delay/2

We use -HHost to emulate this request going to httpbin.digihunch.com (otherwise we’d have to fake DNS entry in /etc/hosts). Both command should give their return without error. The second command will give return after a delay of 2 seconds.

This validates the success of ingress setup.

Egress Testing

To visit an external service, there are four options:

Just access external service from Pods, when you have global.outboundTrafficPolicy.mode=ALLOW_ANY
Use ServiceEntry (as illustrated above in Prep Work)
Bypass envoy proxy (not recommended, because there is no role of service mesh)
Configure an Egress Gateway

In the Prep Work, we’ve seen how to use Service Entry. However, there is no control of how Pods access the external service. We are going to configure an Egress Gateway to manage the outgoing traffic flow. This allows you to manage route, and apply observability features to the outgoing traffic, something the Service Entry alone will not provide. The egress gateway have two typical use cases as explained on Istio website.

First, we want to confirm that the egress pod exists, with a quick command:

kubectl get po -n istio-system -l app=istio-egressgateway && kubectl get se

It should exist as we installed istio as demo version. We then also need a service entry, as we have already configured in Prep Work. At this point, the egress gateway resource has not been created.

Now, in a separate terminal, we monitor the log of egress pod

kubectl logs -f istio-egressgateway-7d5d69dcfd-kvwxv -n istio-system

With the -f (follow) session on, if we visit external service as we did during Prep Work, there is no new entry pop up at the tail of the log. This is because the external access is still not managed by egress. Now we need to add egress, with the following resources applied:

apiVersion: networking.istio.io/v1alpha3
kind: Gateway
metadata:
 name: istio-egressgateway
spec:
 selector:
 istio: egressgateway
 servers:
 - port:
 number: 80
 name: http
 protocol: HTTP
 hosts:
 - httpbin.org

Then we setup the virtual service with related rules:

apiVersion: networking.istio.io/v1alpha3
kind: VirtualService
metadata:
 name: vs-for-egressgateway
spec:
 hosts:
 - "httpbin.org"
 gateways:
 - istio-egressgateway
 - mesh
 http:
 - match:
 - gateways:
 - mesh
 port: 80
 route:
 - destination:
 host: istio-egressgateway.istio-system.svc.cluster.local
 subset: httpbin
 port:
 number: 80
 weight: 100
 - match:
 - gateways:
 - istio-egressgateway
 port: 80
 route:
 - destination:
 host: httpbin.org
 port:
 number: 80
 weight: 100

---
apiVersion: networking.istio.io/v1alpha3
kind: DestinationRule
metadata:
 name: dr-for-egressgateway
spec:
 host: istio-egressgateway.istio-system.svc.cluster.local
 subsets:
 - name: httpbin

With all applied, we can repeat the access command using curl, and watch for the log tail.

kubectl exec -it sleep-557747455f-q99cz -c sleep -- curl http://httpbin.org/ip

The log should output a line saying curl command access, which indicates that this outbound access is managed by istio egress gateway. The log line looks like below and in the example the IP address 10.244.2.4 is the Pod IP address.

[2021-11-22T01:22:47.547Z] "GET /ip HTTP/2" 200 - via_upstream - "-" 0 45 818 816 "10.244.2.9" "curl/7.80.0-DEV" "9ec0a193-77f0-90a5-b132-21c3259307da" "httpbin.org" "3.216.167.140:80" outbound|80||httpbin.org 10.244.2.4:42372 10.244.2.4:8080 10.244.2.9:52710 - -

Looking at the virtual service declaration, you might noticed multiple routes in the virtual service. The first route (mesh) tells sidecars to route request to egress gateway. The second route (istio-egressgateway) tells egress gateway to route traffic to external service as destination.

In real life, there’s more to consider. For example, we usually want the host to allow on egress to be a wild card host such as *.api.google.com. While the hosts field in virtual service can be wild card, the route destination in virtual service has to be a list of fully qualified domains. The other situation is the destination website may issue an HTTP redirect to a different host, which also needs to be registered as a destination. These details can add up to administrative effort.

Egress example

An other real life scenario is the use of authorization policy. Authorization policy rules use SPIFEE identity of a Pod. If a Pod initiates egress connection to destination host in TLS, then the Pod’s SPIFFEE identity and its identity for external TLS connection are in conflict.

With Azure AKS

The steps above also works on other cloud platform such as AKS. This is an AKS cluster that I tested the steps. The Terraform code provisions a private cluster, as well as a Bastion Host. From the Bastion host, we can perform the same steps as above.

When Istio gets installed, it will created a Service object called istio-ingressgateway in the istio-system namespace. The service is of load balancer type and by default will create a public load balancer in Azure AKS.

The test steps will also work for private load balancers. To tell Azure to create private load balancer on a specific subnet, the Service object needs to include annotation. We have to customize Istio installation in order to do that, using the following overlay file (azoverlay.yaml):

apiVersion: install.istio.io/v1alpha2
kind: IstioControlPlane
metadata:
 namespace: istio-operator
 name: custom-istiocontrolplane
spec:
 profile: demo
 values:
 gateways:
 istio-ingressgateway:
 serviceAnnotations:
 service.beta.kubernetes.io/azure-load-balancer-internal: "true"
 service.beta.kubernetes.io/azure-load-balancer-internal-subnet: "suitable-porpoise-lb-subnet"

This is inspired by this post. Then the command to install Istio becomes:

istioctl install -f azoverlay.yaml -y --verify --set meshConfig.outboundTrafficPolicy.mode=REGISTRY_ONLY

This concludes the hand-on guide for Istio ingress and egress labs. I will need to write another post explaining the related concepts.